Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 14 - Jul 19
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
soil moisture meter arduino Soil Moisture Sensor Module for Arduino Raspberry Pi – Makerlab PHProduct DescriptionSoil Moisture Sensor ModuleThis Soil Moisture Sensor Module can be used to detect the moisture of soil or judge if there is water around the sensor, let the plants in your garden reach out for human help. Insert this module into the soil and then adjust the on board potentiometer to adjust the sensitivity. The sensor would output logic HIGH LOW when the moisture is higher lower than the threshold set by the potentiometer. With help
Product DescriptionSoil Moisture Sensor Module
This Soil Moisture Sensor Module can be used to detect the moisture of soil or judge if there is water around the sensor, let the plants in your garden reach out for human help. Insert this module into the soil and then adjust the on-board potentiometer to adjust the sensitivity. The sensor would output logic HIGH/LOW when the moisture is higher/lower than the threshold set by the potentiometer. With help of this sensor, it will be realizable to make the plant remind you: Hey, I am thirsty now, please give me some water.
Features:
Digital output, easy to adjust.
Nickel plating to avoid corrosion.
Working voltage: 3.3V-5V
On-board LM393 chip
Dimension of the board: 3.2cm * 1.4cm
YL-100 Soil Moisture Detection Sensor Module 3pin.
This module is a simple moisture sensor, use measuring moisture and humidity resistance change.
More dry soil, the smaller the output voltage. The more humid the output voltage increases.
The module will be inserted into the soil through the AD converter voltage signal can be detected in soil moisture.
With FOR Arduino, small pumps and other modules automatic watering system
Module size: 60 * 20mm
Operating voltage :3.3-5V
Output voltage: 5V power supply, about 0-3.7V (3.7V voltage is fully immersed in water)
The output voltage is for reference only, because of the different water quality factors, please actual measurements.
This module is a consumable item, will be affected by environmental corrosion, life is about 12 months.
Package Included:
Soil Hygrometer Detection Module Soil Moisture Sensor Analog Output For arduino
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.3 ★★★★★
Based on 526 reviews
Sort
Product Reviews
★★★★★ 5
Works well on 2003 Corvette.
Color: Carbon Fiber, Size: 2 Pack
I purchased these for usage in my 2003 Corvette convertible. As much as I enjoy the vehicle, they are extremely insufficient for storage. No "usable" built-in cup holder, no pockets and no flat area that can hold a cell phone. The console and glove box are not ideal in this day and age since the phones are used constantly. Enter these excellent little holders. They mount perfectly on the central vent in the dash. If you slide the bases as far as possible to each side and then tighten them down, the base will overlap the non-moving portion of the vent and keep the unit quite stable. I would suspect this is applicable for any vehicle that has the traditional flat vent fins. The holder has a hook that when fished into the vent, clasps over the back of one of the fins. By hooking the fin, once tightened down (careful not to over due this as the vents are just plastic) the installation is as stable as you can ask for vs any of those goofy clamp types that slide off quite easily, especially as they age and sun softens the pads. Benefit from my mistakes on those bad purchases and stay away from clamp mounts. If you have flat fin vents and are looking for a reliable means to mount a phone, this may be just right for you.
Best of luck.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 23, 2026
★★★★★ 4
Good product, but...
Color: Dark Black, Size: 1 Pack
Easy to install. Like the product. The holder does not hold the phone position. It flops down alot.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 10, 2026
★★★★★ 5
The Perfect Phone Mount.
Color: Dark Black, Size: 1 Pack
It’s the perfect size, easy to install, and works perfectly. I have a 15 pro max iPhone, and it fits perfectly.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 14, 2026
★★★★★ 5
Well built and removes cleanly.
Color: Dark Black, Size: 1 Pack
Seems to be very solid and it was a little bit tricky to get it located on the vent blade properly, though that might just be due to the vents shape in my Highlander. I really like that it can be easily moved from one vehicle to another if needed without leaving adhesive residue like my last mount did. The only concern I have is whether the vent blade will support the weight long term. Time will tell I guess.
EDIT: This fits all of the vents on my 2011 Highlander great. On my 2022 Highlander it will only attach to the center vents and then just barely hooks on after angling the vent blades enough for the hooks to grab. Even then the mount only makes contact at the very top and bottom of the vent opening. It works, but I wouldn't recommend it as ideal.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 22, 2026
★★★★★ 5
Works great
Color: Dark Black, Size: 1 Pack
Great product which is easy to use and affordable price.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 17, 2026